Bionic grinding machine design for thin shell removal from cassia seeds

Authors

  • Xinyu Yuan 1. College of Engineering, Heilongjiang Bayi Agricultural University, Daqing 163711, Heilongjiang, China
  • Caojun Huang 2. College of Information and Electrical Engineering, Heilongjiang Bayi Agricultural University, Daqing 163711, Heilongjiang, China
  • Xuewen Gao 3. Weichai Lovol Heavy Industry Co., Ltd., Weifang 261200, China
  • Shangyu Tong 4. College of Environmental Ecology, Tibet University, Lhasa 850013, China
  • Yifei Li 1. College of Engineering, Heilongjiang Bayi Agricultural University, Daqing 163711, Heilongjiang, China
  • Shujuan Yi 1. College of Engineering, Heilongjiang Bayi Agricultural University, Daqing 163711, Heilongjiang, China

DOI:

https://doi.org/10.25165/ijabe.v18i6.9532

Keywords:

cassia seed, grinding, automatic control system, test, light reflectivity

Abstract

In order to address the challenge of low efficiency in removing the thin shells from cassia seeds, a bionic grinding machine was developed for the removal of thin shells from cassia seeds during pharmaceutical processing, inspired by the hand-rubbing motion observed in traditional manual methods. The machine features a grinding-suction disk assembly integrated with a negative pressure feeding system. Flow rate calculations were performed to support the design, although specific parameters require further elaboration. A single-chip microcontroller (SCM)-based control system enables real-time parameter adjustment via a human–machine interface, ensuring precise control throughout the grinding process. After prototype fabrication, single-factor experiments established parameter ranges for orthogonal testing. The optimal parameter combination was identified as a grinding layer gap of 2.4 mm, a rotational frequency of 170 r/min, and a grinding duration of 12 s, resulting in a grinding degree of 9.07% and a shell removal cleanliness of 4.51%. Image-based surface feature analysis confirmed the machine’s effectiveness in removing thin shells, supporting its applicability in pharmaceutical seed processing. This study introduces a novel and efficient mechanized approach for cassia seed thin shell removal, which enhances the efficiency of thin shell removal and provides meaningful support for the advancement of pharmaceutical seed processing technologies. Key words: cassia seed; grinding; automatic control system; test; light reflectivity DOI: 10.25165/j.ijabe.20251806.9532 Citation: Yuan X Y, Huang C J, Gao X W, Tong S Y, Li Y F, Yi S J. Bionic grinding machine design for thin shell removal from cassia seeds. Int J Agric & Biol Eng, 2025; 18(6): 269–280.

References

Lam W C, Lyu A P, Bian Z X. ICD-11: impact on traditional Chinese medicine and world healthcare systems. Pharmaceutical medicine, 2019; 33: 373–377.

Zhou X, Li C G, Chang D, Bensoussan A. Current status and major challenges to the safety and efficacy presented by Chinese herbal medicine. Medicines, 2019; 6（1）: 14.

Wu D T, Liu W, Han Q H, Wang P, Xiang X R, Ding Y, et al. Extraction optimization, structural characterization, and antioxidant activities of polysaccharides from cassia seed （Cassia obtusifolia）. Molecules, 2019; 24（15）: 2817.

Pachpor A, Kulkarni D V, Dongre P, Bhaldar N, Khandekar S, Maurya S. A clinical study on effect of Cassia tora Linn: In drug resistance case of tinea corporis. Word Journal of Pharmacy and Pharmaceutical Sciences, 2019; 8（9）: 730–738.

Wu X, Wang S P, Lu J R, Jing Y, Li M X, Cao J L, et al. Seeing the unseen of Chinese herbal medicine processing （Paozhi）: advances in new perspectives. Chinese Medicine, 2018; 13: 4.

Qamar S Z, Pervez T, Chekotu J C. Die defects and die corrections in metal extrusion. Metals, 2018; 8（6）: 380.

Jayasimha S L N, Bawge G, Raju H P. Surface finish characteristics of distinct materials using extrusion honing process. Journal of Computational & Applied Research in Mechanical Engineering （JCARME）, 2021; 12（1）: 41–50.

Hou J M, Liu X, Zhu H J, Ma Z, Tang Z Y, Yu Y C, et al. Design and motion process of air-sieve castor cleaning device based on discrete element method. Agriculture, 2023; 13（6）: 1130.

Balcı F, Bayram M. Modification of mechanical polishing operation using preheating systems to improve the bulgur color. Journal of Cereal Science, 2017; 75（5）: 108–115.

Kang D, Wang Y, Fan Y H, Chen Z J. Research and development of Camellia oleifera fruit sheller and sorting machine. IOP Conference Series: Earth and Environmental Science, 2018; 108（4）: 042051.

Wang G L, Wang Y Q. Research on polishing process of a special polishing machine tool. Machining Science and Technology, 2009; 13（1）: 106–121

Qu X T, Zhang H, Zhao Y B, Zhang F Q. Dynamic design of grinding and polishing machine tool for blisk finishing. IOP Conference Series Materials Science and Engineering, 2018; 382（4）: 042014.

Caringal B K M, Rosa Z S D, Maan K V R, Camello N C. Design and development of rice milling and grinding machine. International Journal of Science and Engineering, 2016; 2（3）: 5–12.

Kalagbor I, Fyneface D, Korfii U, Ogaji T, Kpoonanyie F. Estimation of the levels of Fe in wheat and maize flour milled using commercial milling machine and a home blender. Journal of Applied Sciences and Environmental Management, 2017; 21（2）: 341–344.

Ratnavathi C V. Sorghum processing and utilization. In: Ratnavathi C V, Patil J V, Chavan U D, editors. Sorghum Biochemistry. Academic Press, 2016; pp.311–327. doi: 10.1016/B978-0-12-803157-5.00006-X

Zamri R, Ismail N, Hang Tuah bin Baharudin B T, Mohamed Ariff A H, Prabuwono A S. Analysis of flat and dry polishing parameter influence on surface roughness for robotic polishing cell. Applied Mechanics and Materials, 2014; 564: 543–548.

Dieste J A, Fernández A, Roba D, Gonzalvo B, Lucas P. Automatic grinding and polishing using spherical robot. Procedia Engineering, 2013; 63（9）: 938–946.

Melentiev R, Fang F. Recent advances and challenges of abrasive jet machining. CIRP Journal of Manufacturing Science and Technology, 2018; 22（8）: 1–20.

Alsoufi M S. State-of-the-art in abrasive water jet cutting technology and the promise for micro-and nano-machining. International Journal of Mechanical Engineering and Applications, 2017; 5（1）: 1–14.

Guo C S, Shi Z D, Mullany B, Linke B, Yamaguchi H, Chaudhari R, et al. Recent advancements in machining with abrasives. Journal of Manufacturing Science and Engineering, 2020; 142（11）: 110810.

Krutz G, Thompson L, Claar P. Design of agricultural machinery. John Wiley and Sons: 1984. 480p.

Sciences C. A. o. A. M. Agricultural Machinery Design Manual. 2007.

Hu Y J, Wang Y, Zhu W, Li H. Dynamic modeling of a ball-screw drive and identification of its installation parameters. Journal of Dynamic Systems, Measurement, and Control, 2021; 143（4）: 041003.

Lai C K. The Research of stepper motor subdivision control system for cloth-cutting machines. Applied Mechanics and Materials, 2014; 443（10）: 285–289.

Xu Y F, Zhang X L, Wu S, Chen C, Wang J Z, Yuan S Q, et al. Numerical simulation of particle motion at cucumber straw grinding process based on EDEM. Int J Agric & Biol Eng, 2020; 13（6）: 227–235.

Stockl A, Loeffler D, Oechsner H, Jungbluth T, Fischer K, Kranert M. Near-infrared-reflection spectroscopy as measuring method to determine the state of the process for automatic control of anaerobic digestion. Int J Agric & Biol Eng, 2013; 6（2）: 63–72.

Hou J M, Yao E C, Li J P, Bai J B, Yang Y, Zhu H J. Motion analysis and experiment on shelling process of kneading and pressing castor shelling machine. Transactions of the Chinese Society for Agricultural Machinery, 2018; 51（s2）: 220–232. （in Chinese）

Shi M C, Liu M Z, Li C H, Cao C M, Li X P. Design and experiment of cam rocker bidirectional extrusion walnut shell breaking device. Transactions of the CSAM, 2022; 53（1）: 140–150. （in Chinese）

Wan Z H, Zhang G Z, Xu H M, Zhou Y, Tang N R, Zhang H. Design and experiment of the clamping sheller for fresh water caltrop. Transactions of the CSAE, 2022; 38（20）: 9–19. （in Chinese）

Zhu G F, Ren J J, Wang Z, Xiang H, Mu R S, Li S H. Design of shelling machine for camellia oleifera fruit and operating parameter optimization. Transactions of the CSAE, 2016; 32（7）: 19–27. （in Chinese）

Tang J Y, Wang D, Kou X, Qu Z X, Xu K S. Design and experiment of four-channel fully automatic shelling machine for ripe fresh camellia oleifera fruit. Transactions of the CSAM, 2021; 52（4）: 109–116,229. （in Chinese）

Wang J N, Liu M J, Cao M Z, Yan J C, Peng B L, Hu Z C, et al. Working parameter optimization and experiment of key components of coix lacryma-jobi sheller. Transactions of the CSAE, 2018; 34（13）: 288–295. （in Chinese）

Zhan G C, Ma L N, Huang X M, Zong W Y, Tian W, Lin Z X. Experimental study on impact crushing of rapeseed stalks during threshing of oilseed rape. Transactions of the CSAE, 2020; 36（24）: 11–18. （in Chinese）

Li J, Lu H Z, Yang Z L, Chen Z L, Huang J C. Design and experiment of Canavalia shelling mechanism. Transactions of the CSAE, 2013; 29（1）: 26–32. （in Chinese）

Zhang Q, Ding W, Deng L, Li Y, Zhao Y. Experimental study on friction characteristics of gorgon nuts （Euryale ferox） in mechanical shelling. Transactions of the CSAE, 2013; 29（1）: 56–63. （in Chinese）

Xu X Q, Rao H H, Li T, Liu M H. Design and experiment on automatic husking and peeling machine for lotus seeds. Transactions of the CSAE, 2014; 30（13）: 28–34. （in Chinese）

Zhang L H, Xu Z M, Gou W, Ma Z Y. Optimization of structure parameters of cylinder-bar type shelling device for ginkgo biloba. Transactions of the CSAE, 2012; 28（10）: 39–45. （in Chinese）

Araque O, Arzola N, Cerón I X. Microstructure and mechanical characterization of rice husks from the tolima region of Colombia. Resources, 2024; 13（1）: 16.

Liao P, Meng Y, Chen Y Q, Weng W N, Chen L, Xing Z P, et al. Potted-seedling machine transplantation simultaneously promotes rice yield, grain quality, and lodging resistance in China: A meta-analysis. Agronomy, 2022; 12（12）: 3003.

Liu X P, Shi Z A, Zhang Y L, Li H, Pei H C, Yang H J. Characteristics of damage to brown rice kernels under single and continuous mechanical compression conditions. Foods, 2024; 13（7）: 1069.

Downloads

Published

2025-12-26

How to Cite

Yuan, X., Huang, C., Gao, X., Tong, S., Li, Y., & Yi, S. (2025). Bionic grinding machine design for thin shell removal from cassia seeds. International Journal of Agricultural and Biological Engineering, 18(6), 269–280. https://doi.org/10.25165/ijabe.v18i6.9532

Issue

Vol. 18 No. 6 (2025): IJABE

Section

Agro-product and Food Processing Systems

License

IJABE is an international peer reviewed open access journal, adopting Creative Commons Copyright Notices as follows.


Authors who publish with this journal agree to the following terms:


  1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.

  2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.

  3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).