Numerical simulation and experimental study of the extrusion process for rice straw powder based on EDEM

Chaoran Sun, Wenke Ai, Ping Jiang, Songlin Sun, Limei Chen, Shaohui Tan, Chongfeng Gao

Abstract


The application of twin-screw extrusion technology in the field of straw pretreatment is constrained by the closed nature of its structure, and the internal material flow characteristics have yet to be fully elucidated. This has resulted in a paucity of scientific theoretical support for screw configuration design. To address this issue, this study employed the discrete element method (DEM) in conjunction with physical tests to calibrate the simulation model parameters of rice straw powder. The calibration results demonstrate that the discrepancy between the simulation stacking test and the physical test results is 3.68%, thereby indicating that the simulation model parameters are accurate and reliable. Subsequently, an extrusion verification comparison test of rice straw powder was conducted. The results demonstrated that the relative errors between the simulated and actual quality in different regions ranged from 7.95% to 12.45%. This evidence substantiates the applicability and reliability of the established simulation model in simulating the extrusion process of rice straw powder. Furthermore, the variation rules of the parameters of particle motion and their correlation during the extrusion process of rice straw powder were investigated. It was found that the filling degree was significantly correlated with other parameters, and that the screw configuration had a direct influence on the filling degree. Finally, a bench test was conducted to ascertain the viability of the established simulation model in guiding the design of screw configurations. A linear regression equation was derived between the simulated power consumption and the average particle size of extruded samples under different screw configurations. The study offers a particle-scale understanding of the visualization of the extrusion process of rice straw powder and the scientific design of screw configurations, which is of great significance for the industrial application of the extrusion method.
Key words: rice straw; discrete element method; twin-screw extrusion; parameter calibration; numerical simulation
DOI: 10.25165/j.ijabe.20251802.9381

Citation: Sun C R, Ai W K, Jiang P, Sun S L, Chen L M, Tan S H, et al. Numerical simulation and experimental study of the extrusion process for rice straw powder based on EDEM. Int J Agric & Biol Eng, 2025; 18(2): 288–298.

Keywords


rice straw; discrete element method; twin-screw extrusion; parameter calibration; numerical simulation

Full Text:

PDF

References


Wang F, Liu X F, Chen L G, Lei T Z, Yi W M, Li Z H. Research status and development prospect of energy and high value utilization of biomass resources. Transactions of the CSAE, 2021; 37(18): 219–231. (in Chinese)

Ahmed S F, Rafa N, Mofijur M, Badruddin I A, Inayat A, Ali M S, et al. Biohydrogen production from biomass sources: Metabolic pathways and economic analysis. Frontiers in Energy Research, 2021; 9: 753878.

Sharma R, Singhal S, Tiwari A K, Agarwal S, Arora S, Singhal N. Influence of pretreatment processes onto bio-methanation of wheat straw. Journal of Renewable and Sustainable Energy, 2015; 7(5): 053109.

Hsu T-C, Guo G-L, Chen W-H, Hwang W-S. Effect of dilute acid pretreatment of rice straw on structural properties and enzymatic hydrolysis. Bioresource Technology, 2010; 101(13): 4907–4913.

Shen F, Xiong X, Fu J, Yang J, Qiu M, Qi X, Tsang D C W. Recent advances in mechanochemical production of chemicals and carbon materials from sustainable biomass resources. Renewable and Sustainable Energy Reviews, 2020; 1305: 109944.

Pérez-Merchán A M, Rodríguez-Carballo G, Torres-Olea B, García-Sancho C, Maireles-Torres P J, Mérida-Robles J, et al. Recent advances in mechanochemical pretreatment of lignocellulosic biomass. Energies, 2022; 15(16): 5948.

Zheng J, Choo K, Rehmann L. Xylose removal from lignocellulosic biomass via a twin-screw extruder: The effects of screw configurations and operating conditions. Biomass and Bioenergy, 2016; 88: 10–16.

Geng X Z. Twin screw extruders and their applications. Beijing: China Light Industry Press. 2003; 466.

Elalami D, Aouine M, Monlau F, Guillon F, Dumon C, Hernandez Raquet G, et al. Enhanced enzymatic hydrolysis of corn stover using twin‐screw extrusion under mild conditions. Biofuels, Bioproducts and Biorefining, 2022; 16(6): 1642–1654.

Yağcı S, Sutay Kocabaş D, Çalışkan R, Özbek H N. Statistical investigation of the bioprocess conditions of alkali combined twin‐screw extrusion pretreatment to enhance fractionation and enzymatic hydrolysis of bulgur bran. Journal of the Science of Food and Agriculture, 2022; 102(11): 4770–4779.

Morales-Huerta J C, Hernández-Meléndez O, Hernández-Luna M G, Manero O, Bárzana E, Vivaldo-Lima E. An experimental and modeling study on the pretreatment and alkaline hydrolysis of blue agave bagasse in twin-screw extruders. Industrial & Engineering Chemistry Research, 2021; 60(34): 12449–12460.

Gu B-J, Dhumal G S, Wolcott M P, Ganjyal G M. Disruption of lignocellulosic biomass along the length of the screws with different screw elements in a twin-screw extruder. Bioresource Technology, 2019; 275: 266–271.

Meier R, Moll K-P, Krumme M, Kleinebudde P. Impact of fill-level in twin-screw granulation on critical quality attributes of granules and tablets. European Journal of Pharmaceutics and Biopharmaceutics, 2017; 115: 102–112.

Mundozah A L, Cartwright J J, Tridon C C, Hounslow M J, Salman A D. Hydrophobic/hydrophilic powders: Practical implications of screw element type on the reduction of fines in twin screw granulation. Powder Technology, 2019; 341: 94–103.

Li A Q, Jia F G, Han Y L, Chen P Y, Wang Y L, Zhang J C, et al. Study on dynamic response mechanism of rice grains in friction rice mill and scale-up approach of parameter based on discrete element method. Innovative Food Science & Emerging Technologies, 2023; 86: 103346.

Havlica J, Jirounkova K, Travnickova T, Kohout M. The effect of rotational speed on granular flow in a vertical bladed mixer. Powder Technology, 2015; 280: 180–190.

Li A Q, Jia F G, Wang Y L, Han Y L, Chen P Y, Zhang J C, et al. Numerical analysis of the rice transport uniformity in vertical friction rice mill based on discrete element method. Computers and Electronics in Agriculture, 2022; 202: 107398.

Li X, Hou Q F, Dong K J, Zou R P, Yu A B. Promote cohesive solid flow in a screw feeder with new screw designs. Powder Technology, 2020; 361: 248–257.

Zheng C, Govender N, Zhang L, Wu C-Y. GPU-enhanced dem analysis of flow behaviour of irregularly shaped particles in a full-scale twin screw granulator. Particuology, 2022; 61: 30–40.

Cheng H T, Gong Y J, Zhao N, Zhang L J, Lv D Q, Ren D Z. Simulation and experimental validation on the effect of twin-screw pulping technology upon straw pulping performance based on tavares mathematical model. Processes, 2022; 10(11): 2336.

Rol F, Vergnes B, El Kissi N, Bras J. Nanocellulose production by twin-screw extrusion: simulation of the screw profile to increase the productivity. ACS Sustainable Chemistry & Engineering, 2020; 8(1): 50–59.

Wang W W, Cai D Y, Xie J J, Zhang C L, Liu L C, Chen L Q. Calibration of discrete element model parameters for corn stover powder dense molding. Transactions of the CSAM, 2021; 52(3): 127–134. (in Chinese)

Li Y X, Li F X, Xu X M, Shen C P, Meng K P, Chen J, et al. Calibration of discrete element parameters for wheat flour based on particle scaling. Transactions of the CSAE, 2019; 35(16): 320–327. (in Chinese)

Horabik J, Molenda M. Parameters and contact models for dem simulations of agricultural granular materials: A review. Biosystems Engineering, 2016; 147: 206–225.

Zheng C, Zhang L, Govender N, Wu C-Y. DEM analysis of residence time distribution during twin screw granulation. Powder Technology, 2021; 377: 924–938.

Konan D, Koffi E, Ndao A, Peterson E C, Rodrigue D, Adjallé K. An overview of extrusion as a pretreatment method of lignocellulosic biomass. Energies, 2022; 15(9): 3002.

Said N, Abdel daiem M M, García-Maraver A, Zamorano M. Influence of densification parameters on quality properties of rice straw pellets. Fuel Processing Technology, 2015; 138: 56–64.

Chan Seem T, Rowson N A, Gabbott I, de Matas M, Reynolds G K, Ingram A. Asymmetric distribution in twin screw granulation. European Journal of Pharmaceutics and Biopharmaceutics, 2016; 106: 50–58.

Chen X H, Zhang Y L, Gu Y, Liu Z G, Shen Z, Chu H Q, et al. Enhancing methane production from rice straw by extrusion pretreatment. Applied Energy, 2014; 122: 34–41.

Zhang L, Lu H, Yu J, Wang Z, Fan Y, Zhou X. Dissolution of lignocelluloses with a high lignin content in a N -Methylmorpholine- N -Oxide monohydrate solvent system via simple glycerol-swelling and mechanical pretreatments. Journal of Agricultural and Food Chemistry, 2017; 65(44): 9587–9594.

Matsushita M, Ohsaki S, Nara S, Nakamura H, Watano S. Effect of fill level in continuous twin-screw granulator: A combined experimental and simulation study. Advanced Powder Technology, 2022; 33(11): 103822.

Xu B P, Liang R F, Xiao S P, Feng Y H, Yu H W. Improving mixing by changing topology through intermeshed perturbation rings in a co‐rotating non‐twin screw channel. Macromolecular Theory and Simulations, 2024; 33(2): 2300048.

Yacu W. Extruder screw, barrel, and die assembly: General design principles and operation. In: Ganjyal G M. (Ed.). Extrusion Cooking. Woodhead Publ. & Cereals & Grains Assoc. Bookstore. 2020; pp.73–117. doi: 10.1016/B978-0-12-815360-4.00003-1.




Copyright (c) 2025 International Journal of Agricultural and Biological Engineering

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.

2023-2026 Copyright IJABE Editing and Publishing Office